Beschliesser, M.; Chatterjee, A.; Lorich, A.; Knabl, W.; Kestler, H.; Dehm, G.; Clemens, H.: Designed fully lamellar microstructures in a γ-TiAl based alloy: adjustment and microstructural changes upon long-term isothermal exposure at 700 and 800 degrees C. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 329-331, pp. 124 - 129 (2002)
Dehm, G.; Balk, T. J.; von Blanckenhagen, B.; Gumbsch, P.; Arzt, E.: Dislocation dynamics in sub-micron confinement: recent progress in Cu thin film plasticity. Zeitschrift für Metallkunde/Materials Research and Advanced Techniques 93 (5), pp. 383 - 391 (2002)
Schillinger, W.; Clemens, H.; Dehm, G.; Bartels, A.: Microstructural stability and creep behavior of a lamellar γ-TiAl based alloy with extremely fine lamellar spacing. Intermetallics 10 (5), pp. 459 - 466 (2002)
Bartels, A.; Clemens, H.; Dehm, G.; Lach, E.; Schillinger, W.: Strain rate dependence of the deformation mechanisms in a fully lamellar γ-TiAl-based alloy. Zeitschrift für Metallkunde/Materials Research and Advanced Techniques 93 (3), pp. 180 - 185 (2002)
Dehm, G.; Wagner, T. A.; Balk, T. J.; Arzt, E.; Inkson, B. J.: Plasticity and interfacial dislocation mechanisms in epitaxial and polycrystalline Al films constrained by substrates. Journal of Materials Science & Technology 18 (2), pp. 113 - 117 (2002)
Kobrinsky, M. J.; Dehm, G.; Thompson, C. L.; Arzt, E.: Effects of thickness on the characteristic length scale of dislocation plasticity in Ag thin films. Acta Materialia 49 (17), pp. 3597 - 3607 (2001)
Dehm, G.; Weiss, D.; Arzt, E.: In situ transmission electron microscopy study of thermal-stress-induced dislocations in a thin Cu film constrained by a Si substrate. Materials Science and Engineering A: Structural Materials Properties Microstructure and Processing 309-310, pp. 468 - 472 (2001)
Legros, M.; Dehm, G.; Keller-Flaig, R.-M.; Arzt, E.; Hemker, K. J.; Süresh, S.: Dynamic observation of Al thin films plastically strained in a TEM. Materials Science and Engineering A: Structural Materials Properties Microstructure and Processing 309-310, pp. 463 - 467 (2001)
Scheu, C.; Dehm, G.; Kaplan, W. D.: Equilibrium amorphous silicon-calcium-oxygen films at interfaces in copper-alumina composites prepared by melt infiltration. Journal of the American Ceramic Society 84 (3), pp. 623 - 630 (2001)
Zhang, D.; Dehm, G.; Clemens, H.: On the microstructural evolution and phase transformation in a high niobium containing γ-TiAl alloy. Zeitschrift für Metallkunde 91 (11), pp. 950 - 956 (2000)
Chatterjee, A.; Dehm, G.; Scheu, C.; Clemens, H.: Onset of microstructural instability in a fully lamellar Ti-46.5 at.% Al-4 al.% (Cr,Nb,Ta,B) alloy during short-term creep. Zeitschrift für Metallkunde/Materials Research and Advanced Techniques 91 (9), pp. 755 - 760 (2000)
Dehm, G.; Arzt, E.: In-situ transmission electron microscopy study of dislocations in a polycrystalline Cu thin film constrained by a substrate. Applied Physics Letters 77 (8), pp. 1126 - 1128 (2000)
Zhang, D.; Dehm, G.; Clemens, H.: Effect of heat treatments and hot-isostatic pressing on phase transformations and microstructure in a β/B2 containing γ-TiAl based alloy. Scripta Materialia 42 (11), pp. 1065 - 1070 (2000)
International researcher team presents a novel microstructure design strategy for lean medium-manganese steels with optimized properties in the journal Science
Many important phenomena occurring in polycrystalline materials under large plastic strain, like microstructure, deformation localization and in-grain texture evolution can be predicted by high-resolution modeling of crystals. Unfortunately, the simulation mesh gets distorted during the deformation because of the heterogeneity of the plastic…
About 90% of all mechanical service failures are caused by fatigue. Avoiding fatigue failure requires addressing the wide knowledge gap regarding the micromechanical processes governing damage under cyclic loading, which may be fundamentally different from that under static loading. This is particularly true for deformation-induced martensitic…
Conventional alloy development methodologies which specify a single base element and several alloying elements have been unable to introduce new alloys at an acceptable rate for the increasingly specialised application requirements of modern technologies. An alternative alloy development strategy searches the previously unexplored central regions…
The full potential of energy materials can only be exploited if the interplay between mechanics and chemistry at the interfaces is well known. This leads to more sustainable and efficient energy solutions.