Auinger, M.; Praig, V. G.; Linder, B.; Danninger, H.: Grain boundary oxidation in iron-based alloys, investigated by 18O enriched water vapour - The effect of mixed oxides in binary and ternary Fe–{Al, Cr, Mn, Si} systems. Corrosion Science 96, pp. 133 - 143 (2015)
Bott, J. H.; Yin, H.; Sridhar, S.; Auinger, M.: Theoretical and experimental analysis of selective oxide and nitride formation in Fe–Al alloys. Corrosion Science 91, pp. 37 - 45 (2015)
Auinger, M.; Müller-Lorenz, E. M.; Rohwerder, M.: Modelling and experiment of selective oxidation and nitridation of binary model alloys at 700 degrees C - The systems Fe, 1 wt.%{Al, Cr, Mn, Si}. Corrosion Science 90, pp. 503 - 510 (2015)
Auinger, M.; Vogel, A.; Vogel, D.; Rohwerder, M.: Early stages of oxidation observed by in situ thermogravimetry in low pressure atmospheres. Corrosion Science 86, pp. 183 - 188 (2014)
Auinger, M.; Ebbinghaus, P.; Blümich, A.; Erbe, A.: Effect of surface roughness on optical heating of metals. Journal of the European Optical Society Rapid Publications 9, pp. 14004-1 - 14004-13 (2014)
Auinger, M.; Vogel, A.; Praig, V. G.; Danninger, H.; Rohwerder, M.: Thermogravimetry and insitu mass spectrometry at high temperatures compared to theoretical modelling - The weight loss during selective decarburisation at 800 °C. Corrosion Science 78, pp. 188 - 192 (2014)
Auinger, M.; Vogel, D.; Vogel, A.; Spiegel, M.; Rohwerder, M.: A novel laboratory set-up for investigating surface and interface reactions during short term annealing cycles at high temperatures. Review of Scientific Instruments 84, 085108 (2013)
Auinger, M.; Naraparaju, R.; Christ, H. J.; Rohwerder, M.: Modelling high temperature oxidation in iron-chromium systems: Combined kinetic and thermodynamic calculation of the long-term behaviour and experimental verification. Oxidation of Metals 76 (3-4), pp. 247 - 258 (2011)
Auinger, M.; Rohwerder, M.: Coupling Diffusion and Thermodynamics - Exemplified for the gas nitriding of ironchromium alloys. HTM - Journal of Heat Treatment and Materials 66 (2), pp. 100 - 102 (2011)
Auinger, M.; Borodin, S.; Swaminathan, S.; Rohwerder, M.: Thermodynamic Stability and Reaction Sequence for High Temperature Oxidation Processes in Steels. Materials Science Forum 696, pp. 76 - 81 (2011)
Khan, T. R.; Erbe, A.; Auinger, M.; Marlow, F.; Rohwerder, M.: Electrodeposition of zinc-silica composite coatings: Challenges in incorporating functionalized silica particles into a zinc matrix. Science and Technology of Advanced Materials 12 (5), 055005 (2011)
Merzlikin, S. V.; Vogel, A.; Auinger, M.; Vogel, D.; Rohwerder, M.: Suppressing the selective oxidation during the recrystallization annealing of steel band for improved hot dip galvanizing: Laboratory study. ISHOC2014 - International Symposium on High-temperature Oxidation and Corrosion 2014, Hakodate, Hokkaido Japan (2014)
International researcher team presents a novel microstructure design strategy for lean medium-manganese steels with optimized properties in the journal Science
In this project we study the development of a maraging steel alloy consisting of Fe, Ni and Al, that shows pronounced response to the intrinsic heat treatment imposed during Laser Additive Manufacturing (LAM). Without any further heat treatment, it was possible to produce a maraging steel that is intrinsically precipitation strengthened by an…
The aim of the Additive micromanufacturing (AMMicro) project is to fabricate advanced multimaterial/multiphase MEMS devices with superior impact-resistance and self-damage sensing mechanisms.
TiAl-based alloys currently mature into application. Sufficient strength at high temperatures and ductility at ambient temperatures are crucial issues for these novel light-weight materials. By generation of two-phase lamellar TiAl + Ti3Al microstructures, these issues can be successfully solved. Because oxidation resistance at high temperatures is…
We will investigate the electrothermomechanical response of individual metallic nanowires as a function of microstructural interfaces from the growth processes. This will be accomplished using in situ SEM 4-point probe-based electrical resistivity measurements and 2-point probe-based impedance measurements, as a function of mechanical strain and…