Auinger, M.; Praig, V. G.; Linder, B.; Danninger, H.: Grain boundary oxidation in iron-based alloys, investigated by 18O enriched water vapour - The effect of mixed oxides in binary and ternary Fe–{Al, Cr, Mn, Si} systems. Corrosion Science 96, pp. 133 - 143 (2015)
Bott, J. H.; Yin, H.; Sridhar, S.; Auinger, M.: Theoretical and experimental analysis of selective oxide and nitride formation in Fe–Al alloys. Corrosion Science 91, pp. 37 - 45 (2015)
Auinger, M.; Müller-Lorenz, E. M.; Rohwerder, M.: Modelling and experiment of selective oxidation and nitridation of binary model alloys at 700 degrees C - The systems Fe, 1 wt.%{Al, Cr, Mn, Si}. Corrosion Science 90, pp. 503 - 510 (2015)
Auinger, M.; Vogel, A.; Vogel, D.; Rohwerder, M.: Early stages of oxidation observed by in situ thermogravimetry in low pressure atmospheres. Corrosion Science 86, pp. 183 - 188 (2014)
Auinger, M.; Ebbinghaus, P.; Blümich, A.; Erbe, A.: Effect of surface roughness on optical heating of metals. Journal of the European Optical Society Rapid Publications 9, pp. 14004-1 - 14004-13 (2014)
Auinger, M.; Vogel, A.; Praig, V. G.; Danninger, H.; Rohwerder, M.: Thermogravimetry and insitu mass spectrometry at high temperatures compared to theoretical modelling - The weight loss during selective decarburisation at 800 °C. Corrosion Science 78, pp. 188 - 192 (2014)
Auinger, M.; Vogel, D.; Vogel, A.; Spiegel, M.; Rohwerder, M.: A novel laboratory set-up for investigating surface and interface reactions during short term annealing cycles at high temperatures. Review of Scientific Instruments 84, 085108 (2013)
Auinger, M.; Naraparaju, R.; Christ, H. J.; Rohwerder, M.: Modelling high temperature oxidation in iron-chromium systems: Combined kinetic and thermodynamic calculation of the long-term behaviour and experimental verification. Oxidation of Metals 76 (3-4), pp. 247 - 258 (2011)
Auinger, M.; Rohwerder, M.: Coupling Diffusion and Thermodynamics - Exemplified for the gas nitriding of ironchromium alloys. HTM - Journal of Heat Treatment and Materials 66 (2), pp. 100 - 102 (2011)
Auinger, M.; Borodin, S.; Swaminathan, S.; Rohwerder, M.: Thermodynamic Stability and Reaction Sequence for High Temperature Oxidation Processes in Steels. Materials Science Forum 696, pp. 76 - 81 (2011)
Khan, T. R.; Erbe, A.; Auinger, M.; Marlow, F.; Rohwerder, M.: Electrodeposition of zinc-silica composite coatings: Challenges in incorporating functionalized silica particles into a zinc matrix. Science and Technology of Advanced Materials 12 (5), 055005 (2011)
Merzlikin, S. V.; Vogel, A.; Auinger, M.; Vogel, D.; Rohwerder, M.: Suppressing the selective oxidation during the recrystallization annealing of steel band for improved hot dip galvanizing: Laboratory study. ISHOC2014 - International Symposium on High-temperature Oxidation and Corrosion 2014, Hakodate, Hokkaido Japan (2014)
International researcher team presents a novel microstructure design strategy for lean medium-manganese steels with optimized properties in the journal Science
Smaller is stronger” is well known in micromechanics, but the properties far from the quasi-static regime and the nominal temperatures remain unexplored. This research will bridge this gap on how materials behave under the extreme conditions of strain rate and temperature, to enhance fundamental understanding of their deformation mechanisms. The…
In this project we developed a phase-field model capable of describing multi-component and multi-sublattice ordered phases, by directly incorporating the compound energy CALPHAD formalism based on chemical potentials. We investigated the complex compositional pathway for the formation of the η-phase in Al-Zn-Mg-Cu alloys during commercial…
Hydrogen embrittlement (HE) of steel is a great challenge in engineering applications. However, the HE mechanisms are not fully understood. Conventional studies of HE are mostly based on post mortem observations of the microstructure evolution and those results can be misleading due to intermediate H diffusion. Therefore, experiments with a…
This project aims to investigate the influence of grain boundaries on mechanical behavior at ultra-high strain rates and low temperatures. For this micropillar compressions on copper bi-crystals containing different grain boundaries will be performed.