Ma, D.; Friák, M.; Knezevic, M.; Kalidindi, S. R.; Lebensohn, R. A.; Roters, F.; Neugebauer, J.; Raabe, D.: Polycrystal coarse graining of elastic properties for Ti-Nb biomedical grades using ab-initio single crystal elastic constants. International Plasticity Conference 2009, Virgin Islands, USA (2009)
Nikolov, S.; Sachs, C.; Fabritius, H.; Raabe, D.; Petrov, M.; Friák, M.; Neugebauer, J.: Modeling of the mechanical properties of lobster cuticle from ab initio to macroscale: How nature designs multifunctional composites with optimal properties. International Plasticity Conference 2009, Virgin Islands, USA (2009)
Ohsaki, S.; Raabe, D.; Hono, K.: Mechanical alloying and amorphization in Cu–Nb–Ag in situ composite wires studied by TEM and atom probe tomography. MRS 2009 Fall Meeting, Boston, MA, USA (2009)
Raabe, D.; Demir, E.; Zaefferer, S.: Experimental investigation of geometrically necessary dislocations beneath small indents of different depths using EBSD tomography. MRS 2009 Fall Meeting, Boston, MA, USA (2009)
Hild, S.; Ziegler, A.; Neues, F.; Epple, M.; Fabritius, H.; Raabe, D.: The Crustacean Cuticle: A Model to Study the Influence of Chemical Composition and Microstructure on the Mechanical Properties of a Biological Composite Material. MRS Fall Conference 2008, Boston, MA, USA (2008)
Zambaldi, C.; Roters, F.; Zaefferer, S.; Raabe, D.: Ductility of Gamma-TiAl-Based Microstructures in the Light of Deformation Mode Interaction-Crystal Plasticity Modeling and Micro-Mechanical Experiments. MRS Fall Conference 2008, Boston, MA, USA (2008)
Counts, W. A.; Friák, M.; Battaile, C.; Raabe, D.; Neugebauer, J.: Multiscale Prediction of Polycrystal Elastic Properties of Ultralight Weight Mg-Li Alloys using Ab Initio and FEM Approaches. MRS Fall Conference 2008, Boston, MA, USA (2008)
Demir, E.; Raabe, D.; Zaefferer, S.: Quantification of Geometrically Necessary Dislocations Beneath Small Indents of Different Depths Using EBSD Tomography. MRS Fall Conference 2008, Boston, MA, USA (2008)
Knezevic, M.; Ma, D.; Raabe, D.; Kalidindi, S. R.; Friák, M.; Neugebauer, J.: Application of Spectral Methods for Anisotropy Design of Ti-Nb Polycrystals for Biomedical Applications based on ab Initio Elastic Single Crystal Constants and Fast Fourier Homogenization. MRS Fall Conference 2008, Boston, MA, USA (2008)
Petrov, M.; Friák, M.; Lymperakis, L.; Neugebauer, J.; Raabe, D.: Ground-state structure and elastic anisotropy of crystalline alpha-chitin: An ab-initio based conformational analysis. Materials Research Society meeting (MRS), Boston, MA, USA (2008)
Calcagnotto, M.; Ponge, D.; Raabe, D.: Mechanical properties of ultrafine and fine grained dual phase steels. MS&T 2008 (Materials Science and Technology), Pittsburgh, PA, USA (2008)
Ma, A.; Friák, M.; Neugebauer, J.; Raabe, D.: Ab initio based design of alloys. MS&T'08, Symposium: Discovery and Optimization of Materials Through Computational Design, David Lawrence Convention Center, Pittsburgh, PA, USA (2008)
Hydrogen in aluminium can cause embrittlement and critical failure. However, the behaviour of hydrogen in aluminium was not yet understood. Scientists at the Max-Planck-Institut für Eisenforschung were able to locate hydrogen inside aluminium’s microstructure and designed strategies to trap the hydrogen atoms inside the microstructure. This can…
Understanding hydrogen-microstructure interactions in metallic alloys and composites is a key issue in the development of low-carbon-emission energy by e.g. fuel cells, or the prevention of detrimental phenomena such as hydrogen embrittlement. We develop and test infrastructure, through in-situ nanoindentation and related techniques, to study…
Recently developed dual-phase high entropy alloys (HEAs) exhibit both an increase in strength and ductility upon grain refinement, overcoming the strength-ductility trade-off in conventional alloys [1]. Metastability engineering through compositional tuning in non-equimolar Fe-Mn-Co-Cr HEAs enabled the design of a dual-phase alloy composed of…
Because of their excellent corrosion resistance, high wear resistance and comparable low density, Fe–Al-based alloys are an interesting alternative for replacing stainless steels and possibly even Ni-base superalloys. Recent progress in increasing strength at high temperatures has evoked interest by industries to evaluate possibilities to employ…
To design novel alloys with tailored properties and microstructure, two materials science approaches have proven immensely successful: Firstly, thermodynamic and kinetic descriptions for tailoring and processing alloys to achieve a desired microstructure. Secondly, crystal defect manipulation to control strength, formability and corrosion…