Publications of Lutz Morsdorf

Kiranbabu, S.; Qin, Y.; Sreekala, L.; Das, S. M.; Pippan, R.; Morsdorf, L.; Herbig, M.: Decomposition-resistant carbonitride precipitates in X30CrMoN15-1 high-nitrogen bearing steel deformed by high-pressure torsion. Materials Science and Engineering A: Structural Materials Properties Microstructure and Processing 863, 144529 (2023)

Srikakulapu, K.; Tung, P.-Y.; Sreekala, L.; Prithiv, T. S.; Hickel, T.; Pippan, R.; Morsdorf, L.; Herbig, M.: Cementite decomposition in 100Cr6 bearing steel during high-pressure torsion: Influence of precipitate composition, size, morphology and matrix hardness. Materials Science and Engineering A: Structural Materials Properties Microstructure and Processing 833, 142372 (2022)

Tung, P.-Y.; Zhou, X.; Mayweg, D.; Morsdorf, L.; Herbig, M.: Under-stoichiometric cementite in decomposing binary Fe–C pearlite exposed to rolling contact fatigue. Acta Materialia 216, 117144 (2021)

Mayweg, D.; Morsdorf, L.; Li, Y.; Herbig, M.: Correlation between grain size and carbon content in white etching areas in bearings. Acta Materialia 215, 117048 (2021)

Morsdorf, L.; Emelina, E.; Gault, B.; Herbig, M.; Tasan, C. C.: Carbon redistribution in quenched and tempered lath martensite. Acta Materialia 205, 116521 (2021)

Mayweg, D.; Morsdorf, L.; Wu, X.; Herbig, M.: The role of carbon in the white etching crack phenomenon in bearing steels. Acta Materialia 203, 116480 (2021)

Morsdorf, L.; Mayweg, D.; Li, Y.; Diederichs, A.; Raabe, D.; Herbig, M.: Moving cracks form white etching areas during rolling contact fatigue in bearings. Materials Science and Engineering A: Structural Materials Properties Microstructure and Processing 771, 138659 (2020)

Benzing, J. T.; Kwiatkowski da Silva, A.; Morsdorf, L.; Bentley, J.; Ponge, D.; Dutta, A.; Han, J.; McBride, J. R.; Van Leer, B.; Gault, B. et al.; Raabe, D.; Wittig, J. E.: Multi-scale characterization of austenite reversion and martensite recovery in a cold-rolled medium-Mn steel. Acta Materialia 166, pp. 512 - 530 (2019)

Lu, W.; Herbig, M.; Liebscher, C.; Morsdorf, L.; Marceau, R. K. W.; Dehm, G.; Raabe, D.: Formation of eta carbide in ferrous martensite by room temperature aging. Acta Materialia 158, pp. 297 - 312 (2018)

Khosravani, A.; Morsdorf, L.; Tasan, C. C.; Kalidindi, S. R.: Multiresolution mechanical characterization of hierarchical materials: Spherical nanoindentation on martensitic Fe–Ni–C steels. Acta Materialia 153, pp. 257 - 269 (2018)

van Bohemen, S. M. C.; Morsdorf, L.: Predicting the M_s temperature of steels with a thermodynamic based model including the effect of the prior austenite grain size. Acta Materialia 125, pp. 401 - 415 (2017)

Morsdorf, L.; Jeannin, O.; Barbier, D.; Mitsuhara, M.; Raabe, D.; Tasan, C. C.: Multiple mechanisms of lath martensite plasticity. Acta Materialia 121, pp. 202 - 214 (2016)

Morsdorf, L.; Pradeep, K. G.; Herzer, G.; Kovács, A.; Dunin-Borkowski, R. E.; Povstugar, I.; Konygin, G.; Choi, P.-P.: Phase selection and nanocrystallization in Cu-free soft magnetic FeSiNbB amorphous alloy upon rapid annealing. Journal of Applied Physics 119, 124903 (2016)

Zhang, J.; Morsdorf, L.; Tasan, C. C.: Multi-probe microstructure tracking during heat treatment without an in-situ setup: Case studies on martensitic steel, dual phase steel and β-Ti alloy. Materials Characterization 111, pp. 137 - 146 (2016)

Morsdorf, L.; Tasan, C. C.; Ponge, D.; Raabe, D.: 3D structural and atomic-scale analysis of lath martensite: Effect of the transformation sequence. Acta Materialia 95, pp. 366 - 377 (2015)

Morsdorf, L.; Gault, B.; Ponge, D.; Tasan, C. C.; Raabe, D.: Improved Atom Probe Methodology for Studying Carbon Redistribution in Low-Carbon High-Ms Lath Martensitic Steels. In: Microscopy & Microanalysis 2017, Vol. 23, pp. 706 - 707. Microscopy & Microanalysis 2017, St. Louis, Missouri, USA, August 06, 2017 - August 10, 2017. Cambridge University Press, Cambridge, UK (2017)

Diehl, M.; Naunheim, Y.; Yan, D.; Morsdorf, L.; An, D.; Tasan, C. C.; Zaefferer, S.; Roters, F.; Raabe, D.: Coupled Experimental-Numerical Analysis of Strain Partitioning in Metallic Microstructures: The Importance of Considering the 3D Morphology. In: Session 1.3a, Strain Measurement at the Microscale 1, pp. 1 - 2. BSSM 12th International Conference on Advances in Experimental Mechanics, Sheffield, UK, August 29, 2017. (2017)

Herbig, M.; Marceau, R. K. W.; Morsdorf, L.; Raabe, D.: Spinodal Decomposition of Fe–Ni–C Martensite by Room Temperature Redistribution of Carbon Investigated by Correlative ECCI/TEM/APT. In: Proceedings of the International Conference on Solid-Solid Phase Transformations in Inorganic Materials 2015, pp. 299 - 300. PTM 2015 - Proceedings of the International Conference on Solid-Solid Phase Transformations in Inorganic Materials 2015, Whistler, BC, Canada, June 28, 2015 - July 03, 2015. International Conference on Solid-Solid Phase Transformations in Inorganic Materials 2015, Whistler, BC, Canada (2015)

Srikakulapu, K.; Morsdorf, L.; Herbig, M.: Cementite decomposition in 100Cr6 bearing steel during high-pressure torsion: Influence of precipitate composition, size, morphology and matrix hardness. The Minerals, Metals & Materials Society, TMS 2022, online, Anaheim, CA, USA (2022)

Morsdorf, L.; Mayweg, D.; Li, Y.; Diederichs, A.; Raabe, D.; Herbig, M.: Moving cracks and missing C atoms – chasing the mysteries of white etching areas in bearings. 2nd meeting of "Metallurgical Metallurgy for Plasticity-driven Damage and Fracture" research forum 2021 (ISIJ), virtual (2021)