Journal Article (184)
61.
Journal Article
194, pp. 257 - 275 (2020)
The effect of solid solution and gamma prime on the deformation modes in Ni-based superalloys. Acta Materialia 62.
Journal Article
185, pp. 88 - 93 (2020)
On the rhenium segregation at the low angle grain boundary in a single crystal Ni-base superalloy. Scripta Materialia 63.
Journal Article
26 (S2), pp. 3078 - 3080 (2020)
Unveiling True Three-dimensional Microstructural Evolution in Novel Chalcogenide Nanocomposites as a Route to Infrared Gradient Refractive Index Functionality. Microscopy and Microanalysis 64.
Journal Article
12, 100700 (2020)
From single phase to dual-phase TRIP-TWIP titanium alloys: Design approach and properties. Materialia 65.
Journal Article
194, pp. 106 - 117 (2020)
High-rate superplasticity in an equiatomic medium-entropy VCoNi alloy enabled through dynamic recrystallization of a duplex microstructure of ordered phases. Acta Materialia 66.
Journal Article
34, 101198 (2020)
Selective laser melting of CP–Ti to overcome the low cost and high performance trade-off. Additive Manufacturing 67.
Journal Article
26 (S2), pp. 2078 - 2079 (2020)
Exploration of Novel Ordering Mechanism in Titanium Alloys Using Atom Probe Tomography and Aberration-corrected Scanning Transmission Electron Microscopy. Microscopy and Microanalysis 68.
Journal Article
50, pp. 59 - 65 (2020)
Unveiling the underlying mechanism of forming edge cracks upon high strain-rate rolling of magnesium alloy. Journal of Materials Science & Technology 69.
Journal Article
10, 12140 (2020)
A new class of lightweight, stainless steels with ultra-high strength and large ductility. Scientific Reports 70.
Journal Article
11 (1), 3634 (2020)
Chemical instability at chalcogenide surfaces impacts chalcopyrite devices well beyond the surface. Nature Communications 71.
Journal Article
51, pp. 5056 - 5076 (2020)
Microstructural Evolution in an Fe–10Ni–0.1C Steel During Heat Treatment and High Strain-Rate Deformation. Metallurgical and Materials Transactions A 72.
Journal Article
790, 139578 (2020)
Development of new γ′-strengthened Co-based superalloys with low mass density, high solvus temperature and high temperature strength. Materials Science and Engineering A: Structural Materials Properties Microstructure and Processing 73.
Journal Article
165, 110369 (2020)
Aging induced segregation and nanoprecipitation in a severely deformed equiatomic high-entropy alloy. Materials Characterization 74.
Journal Article
193, pp. 83 - 98 (2020)
Developing a high-strength Al–Mg–Si–Sc–Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms. Acta Materialia 75.
Journal Article
130, 102703 (2020)
Crystal plasticity finite element analysis of gradient nanostructured TWIP steel. International Journal of Plasticity 76.
Journal Article
111 (7), pp. 587 - 593 (2020)
Laser additive manufacturing of copper–chromium–niobium alloys using gas atomized powder. International Journal of Materials Research 77.
Journal Article
183, pp. 17 - 21 (2020)
Ductility of an ultrastrong glass-crystal nano-dual-phase alloy in sub-micron. Scripta Materialia 78.
Journal Article
582, pp. 515 - 519 (2020)
High-strength Damascus steel by additive manufacturing. Nature 79.
Journal Article
6 (25), eaba7802 (2020)
Snoek-type damping performance in strong and ductile high-entropy alloys. Science Advances 80.
Journal Article
11, 3081 (2020)
A strong and ductile medium-entropy alloy resists hydrogen embrittlement and corrosion. Nature Communications