Publications

Thesis - PhD (98)

1. 3421.
   MPG.PuRe
   Thesis - PhD

   Larour, P.: Strain rate sensitivity of automotive sheet steels: Influence of plastic strain, strain rate, temperature, microstructure, bake hardening and pre-strain. Dissertation, RWTH Aachen, Aachen, Germany (2010)
2. 3422.
   MPG.PuRe
   Thesis - PhD

   Tasan, C. C.: Micromechanical Characterization of Ductile Damage in Sheet Metal. Dissertation, TU Delft, Delft, The Netherlands (2010)
3. 3423.
   MPG.PuRe
   Thesis - PhD

   Aghajani, A.: Evolution of microstructure during long-term creep of a tempered martensite ferritic steel. Dissertation, Ruhr-University Bochum, Bochum (2009)
4. 3424.
   MPG.PuRe
   Thesis - PhD

   Huynh, N. N.: Modelling of Microstructure Evolution and Crack Opening in FCC Materials under Tension. Dissertation, Wollongong University, Wollongong New South Wales [Australia] (2009)
5. 3425.
   MPG.PuRe
   Thesis - PhD

   Balasundaram, K.: Mechanical Characterization of Viscoelastic-Plastic Soft Matter using Nanoindentation. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)
6. 3426.
   MPG.PuRe
   Thesis - PhD

   Liu, T.: High Resolution Investigation of Texture Formation Process in Diamond Films and the Related Macro-Stresses. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)
7. 3427.
   MPG.PuRe
   Thesis - PhD

   Imlau, J.: Zusammenhang zwischen Mikrostruktur, Schädigungsverlauf und mechanischen Eigenschaften bei TRIP Stählen. Dissertation, RWTH Aachen, Aachen, Germany (2008)
8. 3428.
   MPG.PuRe
   Thesis - PhD

   Thomas, I.: Untersuchung metallphysikalischer und messtechnischer Grundlagen zur Rekristallisation und Erholung mikrolegierter IF Stähle. Dissertation, RWTH Aachen, Aachen, Germany (2008)
9. 3429.
   MPG.PuRe
   Thesis - PhD

   Cedat, D.: Modeling and Experiment on Mo-based high temperature composites. Dissertation, Ecole Centrale Paris, Laboratoire for Materials, Paris [France] (2008)
10. 3430.
    MPG.PuRe
    Thesis - PhD

    Raue, L.: Kristallographische Texturen und richtungsabhängige mechanische Eigenschaften des Exoskeletts des amerikanischen Hummers sowie Texturen weiterer Biomaterialien. Dissertation, RWTH Aachen, Aachen, Germany (2008)
11. 3431.
    MPG.PuRe
    Thesis - PhD

    Sachs, C.: Microstructure and mechanical properties of the exoskeleton of the lobster Homarus americanus as an example of a biological composite material. Dissertation, RWTH Aachen, Aachen, Germany (2008)
12. 3432.
    MPG.PuRe
    Thesis - PhD

    Zaafarani, N.: Experimental and theoretical investigation of nanoindentation in a Cu single crystal. Dissertation, RWTH Aachen, Aachen, Germany (2008)
13. 3433.
    MPG.PuRe
    Thesis - PhD

    Tjahjanto, D.: Micromechanical Modeling and Simulations of Tranformation-Induced Plasticity in Multiphase Carbon Steels. Dissertation, TU Delft, Delft, The Netherlands (2008)
14. 3434.
    MPG.PuRe
    Thesis - PhD

    Klüber, C.: Korrelation von mechanischen Eigenschaften und Kristallorientierung auf mikroskopischer und nanoskopischer Ebene. Dissertation, RWTH Aachen, Aachen, Germany (2008)
15. 3435.
    MPG.PuRe
    Thesis - PhD

    Bastos da Silva, A. F.: Characterization of the Microstructure, Grain Boundaries and Texture of Nanostructured Electrodeposited CoNi by use of EBSD. Dissertation, RWTH Aachen, Aachen, Germany (2007)
16. 3436.
    MPG.PuRe
    Thesis - PhD

    Al-Sawalmih, A.: Crystallographic Texture of the Arthropod Cuticle Using Synchrotron Wide Angle X-ray Diffraction. Dissertation, RWTH Aachen, Aachen, Germany (2007)
17. 3437.
    MPG.PuRe
    Thesis - PhD

    Detroy, S.: Charakterisierung und Entwicklung von bainitischen Multiphasen-Stählen. Dissertation, RWTH Aachen, Aachen, Germany (2007)
18. 3438.
    MPG.PuRe
    Thesis - PhD

    Godara, A.: Polymer crystallization and micromechanical behavior of fiber-reinforced polymer composites – a microstructural view on advanced polymer composites. Dissertation, RWTH Aachen, Aachen, Germany (2007)
19. 3439.
    MPG.PuRe
    Thesis - PhD

    Goerdeler, M.: Application of a dislocation density based flow stress model in the integrative through-process modeling of Aluminium production. Dissertation, RWTH Aachen, Aachen, Germany (2007)
20. 3440.
    MPG.PuRe
    Thesis - PhD

    Yusupov, A.: Berechnung der Breitung und der Breitenform beim Warmflachwalzen von Stahl. Dissertation, TUBA Freiberg, Freiberg (2007)