Publications

Publications

Thesis - PhD (96)

  1. 3321.
    Thesis - PhD
    Springer, H.: Fundamental Research into the Role of Intermetallic Phases in Joining of Aluminium Alloys to Steel. Dissertation, Ruhr-University Bochum, Bochum, Germany (2011)
  2. 3322.
    Thesis - PhD
    Lü, Y.: Deformation and recrystallization behaviour of Fe–Mn–C alloys. Dissertation, RWTH Aachen, Aachen, Germany (2011)
  3. 3323.
    Thesis - PhD
    Calcagnotto, M.: Ultrafine grained dual-phase steels. Dissertation, RWTH Aachen, Aachen, Germany (2010)
  4. 3324.
    Thesis - PhD
    Zambaldi, C.: Micromechanical Modeling of Gamma-TiAl - based alloys. Dissertation, RWTH Aachen, Aachen, Germany (2010)
  5. 3325.
    Thesis - PhD
    Demir, E.: Constitutive modeling of fcc single crystals and experimental study of mechanical size effects. Dissertation, RWTH Aachen, Aachen, Germany (2010)
  6. 3326.
    Thesis - PhD
    Larour, P.: Strain rate sensitivity of automotive sheet steels: Influence of plastic strain, strain rate, temperature, microstructure, bake hardening and pre-strain. Dissertation, RWTH Aachen, Aachen, Germany (2010)
  7. 3327.
    Thesis - PhD
    Tasan, C. C.: Micromechanical Characterization of Ductile Damage in Sheet Metal. Dissertation, TU Delft, Delft, The Netherlands (2010)
  8. 3328.
    Thesis - PhD
    Aghajani, A.: Evolution of microstructure during long-term creep of a tempered martensite ferritic steel. Dissertation, Ruhr-University Bochum, Bochum (2009)
  9. 3329.
    Thesis - PhD
    Huynh, N. N.: Modelling of Microstructure Evolution and Crack Opening in FCC Materials under Tension. Dissertation, Wollongong University, Wollongong New South Wales [Australia] (2009)
  10. 3330.
    Thesis - PhD
    Balasundaram, K.: Mechanical Characterization of Viscoelastic-Plastic Soft Matter using Nanoindentation. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)
  11. 3331.
    Thesis - PhD
    Liu, T.: High Resolution Investigation of Texture Formation Process in Diamond Films and the Related Macro-Stresses. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)
  12. 3332.
    Thesis - PhD
    Imlau, J.: Zusammenhang zwischen Mikrostruktur, Schädigungsverlauf und mechanischen Eigenschaften bei TRIP Stählen. Dissertation, RWTH Aachen, Aachen, Germany (2008)
  13. 3333.
    Thesis - PhD
    Thomas, I.: Untersuchung metallphysikalischer und messtechnischer Grundlagen zur Rekristallisation und Erholung mikrolegierter IF Stähle. Dissertation, RWTH Aachen, Aachen, Germany (2008)
  14. 3334.
    Thesis - PhD
    Cedat, D.: Modeling and Experiment on Mo-based high temperature composites. Dissertation, Ecole Centrale Paris, Laboratoire for Materials, Paris [France] (2008)
  15. 3335.
    Thesis - PhD
    Raue, L.: Kristallographische Texturen und richtungsabhängige mechanische Eigenschaften des Exoskeletts des amerikanischen Hummers sowie Texturen weiterer Biomaterialien. Dissertation, RWTH Aachen, Aachen, Germany (2008)
  16. 3336.
    Thesis - PhD
    Sachs, C.: Microstructure and mechanical properties of the exoskeleton of the lobster Homarus americanus as an example of a biological composite material. Dissertation, RWTH Aachen, Aachen, Germany (2008)
  17. 3337.
    Thesis - PhD
    Zaafarani, N.: Experimental and theoretical investigation of nanoindentation in a Cu single crystal. Dissertation, RWTH Aachen, Aachen, Germany (2008)
  18. 3338.
    Thesis - PhD
    Tjahjanto, D.: Micromechanical Modeling and Simulations of Tranformation-Induced Plasticity in Multiphase Carbon Steels. Dissertation, TU Delft, Delft, The Netherlands (2008)
  19. 3339.
    Thesis - PhD
    Klüber, C.: Korrelation von mechanischen Eigenschaften und Kristallorientierung auf mikroskopischer und nanoskopischer Ebene. Dissertation, RWTH Aachen, Aachen, Germany (2008)
  20. 3340.
    Thesis - PhD
    Bastos da Silva, A. F.: Characterization of the Microstructure, Grain Boundaries and Texture of Nanostructured Electrodeposited CoNi by use of EBSD. Dissertation, RWTH Aachen, Aachen, Germany (2007)
 
Go to Editor View
loading content