Publications

Search results

Thesis - PhD (93)

  1. 2121.
    Thesis - PhD
    Wolff, C.: Der tribologisch asymmetrische Flachstauchversuch - Eine neue Methode zur Analyse von Reibungsvorgängen bei Umformprozessen. Dissertation, RWTH Aachen, Aachen, Germany (2001)

Thesis - Diploma (2)

  1. 2122.
    Thesis - Diploma
    Kaushal, C.: Untersuchung der Abhängigkeit des Ölaustrags von der Oberflächenfeinstruktur beim Auswalzen gedoppelter Aluminiumfolien. Diploma, HS Niederrhein, Krefeld, Germany (2003)
  2. 2123.
    Thesis - Diploma
    Tranchant, J.: Deformation of Semi-Brittle Intermetallic Material under Superimposed Hydrostatic Pressure. Diploma, Ecole Centrale de Nantes, Nantes, France (2002)

Thesis - Master (8)

  1. 2124.
    Thesis - Master
    Qin, S.: Measurement of solidification characteristics of steel during Selective Laser Melting using high-speed pyrometry. Master, RWTH Aachen, Aachen, Germany (2018)
  2. 2125.
    Thesis - Master
    Ackers, M.: Recommissioning of a metal powder atomisation system and investigation of its suitability to produce powders for additive Manufacturing processes. Master, Ruhr-Universität Bochum, Bochum, Germany (2017)
  3. 2126.
    Thesis - Master
    Qin, Y.: Effect of post-heat treatment on the microstructure and mechanical properties of SLM-produced IN738LC. Master, RWTH Aachen, Aachen, Germany (2017)
  4. 2127.
    Thesis - Master
    Wu, L.: Characterization of the microstructure and impurities of Al–Mg–Sc alloy produced by Laser Additive Manufacturing. Master, RWTH Aachen, Aachen, Germany (2016)
  5. 2128.
    Thesis - Master
    Lu, L.: Characterization of the crack formation mechanism in Ni-based superalloy Inconel 738LC produced by Selective Laser Melting (SLM). Master, Institut für Eisenhüttenkunde, RWTH Aachen, Aachen, Germany (2015)
  6. 2129.
    Thesis - Master
    Sheng, Z.: Characterization of the Microstructure and Mechanical Properties of Maraging Steels Produced by Laser Additive Manufacturing. Master, RWTH Aachen University, Aachen, Germany (2014)
  7. 2130.
    Thesis - Master
    Archie, F. M. F.: Nanostructured High-Mn Steels by High Pressure Torsion: Microstructure-Mechanical Property Relations. Master, Materials Chemistry, Lehrstuhl für Werkstoffchemie, RWTH Aachen, Aachen, Germany (2014)
  8. 2131.
    Thesis - Master
    Siboni, N. H.: Statistical and Quantum Mechanical Simulation of Interstitials in Metals - Mechanisms and Constraints for Superabundant Vacancy Formation. Master, RWTH Aachen, Institute for Computational Engineering Science, Aachen, Germany (2010)

Thesis - Bachelor (2)

  1. 2132.
    Thesis - Bachelor
    Sander, B.: Gefüge- und Eigenschaftsuntersuchungen an den Ti-20Mo-7Zr-5Ta und Ti-35Nb-7Zr-5Ta β-Titanlegierungen für medizinische Implantate. Bachelor, FH Düsseldorf, Düsseldorf (2008)
  2. 2133.
    Thesis - Bachelor
    Weber, F.: Metallphysikalische Untersuchungen der Platizität von Einkristallen in mikroskopischen Dimensionen unter Verwendung von FEM Simulation. Bachelor, FH Düsseldorf, Düsseldorf [Germany] (2007)

Report (21)

  1. 2134.
    Report
    Raabe, D.; Sander, B.; Friák, M.; Ma, D.; Neugebauer, J.: Ab-initio simulation and experimental validation of beta-titanium alloys. (2008)
  2. 2135.
    Report
    Herrera, C.; Ponge, D.; Raabe, D.: Potential HDD - High Ductility Duplex. (2007)
  3. 2136.
    Report
    Konrad, J.; Guenther, A.; Zaefferer, S.; Raabe, D.: Texture analysis of a coarse grained Fe3Al cast alloy by neutron scattering. MPI für Eisenforschung GmbH, Düsseldorf, Germany (2004)
  4. 2137.
    Report
    Kuo, J. C.; Zaefferer, S.; Raabe, D.: Plastic deformation of aluminium-bicrystals. (2004)
  5. 2138.
    Report
    Kuo, J. C.; Zaefferer, S.; Raabe, D.: Experimental investigation of the deformation behavior of aluminium-bicrystals. MPI für Eisenforschung GmbH, Düsseldorf, Germany (2004)
  6. 2139.
    Report
    Ma, A.; Roters, F.; Raabe, D.: Simulation of textures and Lankford values for face centered cubic polycrystaline metals by using a modified Taylor model. (2004)
  7. 2140.
    Report
    Raabe, D.: A 3D probabilistic cellular automaton for the simulation of recrystallization and grain growth phenomena. Max-Planck-Society, München, Germany (2004)
 
loading content
Go to Editor View