Publications of D. Raabe

Thesis - PhD (113)

2281.
Thesis - PhD
Khorashadizadeh, A.: Microstructure characterization of ultra-fine grained Cu–0.17wt.%Zr. Dissertation, RWTH Aachen, Aachen, Germany (2011)
2282.
Thesis - PhD
Song, J.: Microstructure and properties of interfaces formed by explosion cladding of Titanium to low Carbon steel. Dissertation, Ruhr-University Bochum, Bochum, Germany (2011)
2283.
Thesis - PhD
Voß, S.: Mechanische Eigenschaften von Laves-Phasen in Abhängigkeit von Kristallstruktur und Zusammensetzung am Beispiel der Systeme Fe–Nb–Al und Co–Nb. Dissertation, RWTH Aachen, Aachen, Germany (2011)
2284.
Thesis - PhD
Saeed-Akbari, A.: Mechanism Maps, Mechanical Properties, and Flow Behavior in High-Manganese TRIP/TWIP and TWIP steels. Dissertation, RWTH Aachen, Aachen, Germany (2011)
2285.
Thesis - PhD
Springer, H.: Fundamental Research into the Role of Intermetallic Phases in Joining of Aluminium Alloys to Steel. Dissertation, Ruhr-University Bochum, Bochum, Germany (2011)
2286.
Thesis - PhD
Lü, Y.: Deformation and recrystallization behaviour of Fe–Mn–C alloys. Dissertation, RWTH Aachen, Aachen, Germany (2011)
2287.
Thesis - PhD
Zambaldi, C.: Micromechanical Modeling of Gamma-TiAl - based alloys. Dissertation, RWTH Aachen, Aachen, Germany (2010)
2288.
Thesis - PhD
Demir, E.: Constitutive modeling of fcc single crystals and experimental study of mechanical size effects. Dissertation, RWTH Aachen, Aachen, Germany (2010)
2289.
Thesis - PhD
Larour, P.: Strain rate sensitivity of automotive sheet steels: Influence of plastic strain, strain rate, temperature, microstructure, bake hardening and pre-strain. Dissertation, RWTH Aachen, Aachen, Germany (2010)
2290.
Thesis - PhD
Tasan, C. C.: Micromechanical Characterization of Ductile Damage in Sheet Metal. Dissertation, TU Delft, Delft, The Netherlands (2010)
2291.
Thesis - PhD
Aghajani, A.: Evolution of microstructure during long-term creep of a tempered martensite ferritic steel. Dissertation, Ruhr-University Bochum, Bochum (2009)
2292.
Thesis - PhD
Huynh, N. N.: Modelling of Microstructure Evolution and Crack Opening in FCC Materials under Tension. Dissertation, Wollongong University, Wollongong New South Wales [Australia] (2009)
2293.
Thesis - PhD
Balasundaram, K.: Mechanical Characterization of Viscoelastic-Plastic Soft Matter using Nanoindentation. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)
2294.
Thesis - PhD
Liu, T.: High Resolution Investigation of Texture Formation Process in Diamond Films and the Related Macro-Stresses. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)
2295.
Thesis - PhD
Imlau, J.: Zusammenhang zwischen Mikrostruktur, Schädigungsverlauf und mechanischen Eigenschaften bei TRIP Stählen. Dissertation, RWTH Aachen, Aachen, Germany (2008)
2296.
Thesis - PhD
Thomas, I.: Untersuchung metallphysikalischer und messtechnischer Grundlagen zur Rekristallisation und Erholung mikrolegierter IF Stähle. Dissertation, RWTH Aachen, Aachen, Germany (2008)
2297.
Thesis - PhD
Cedat, D.: Modeling and Experiment on Mo-based high temperature composites. Dissertation, Ecole Centrale Paris, Laboratoire for Materials, Paris [France] (2008)
2298.
Thesis - PhD
Raue, L.: Kristallographische Texturen und richtungsabhängige mechanische Eigenschaften des Exoskeletts des amerikanischen Hummers sowie Texturen weiterer Biomaterialien. Dissertation, RWTH Aachen, Aachen, Germany (2008)
2299.
Thesis - PhD
Sachs, C.: Microstructure and mechanical properties of the exoskeleton of the lobster Homarus americanus as an example of a biological composite material. Dissertation, RWTH Aachen, Aachen, Germany (2008)
2300.
Thesis - PhD
Zaafarani, N.: Experimental and theoretical investigation of nanoindentation in a Cu single crystal. Dissertation, RWTH Aachen, Aachen, Germany (2008)
Go to Editor View