Publikationen von D. Raabe

Lü, Y.: Deformation and recrystallization behaviour of Fe–Mn–C alloys. Dissertation, RWTH Aachen, Aachen, Germany (2011)

Zambaldi, C.: Micromechanical Modeling of Gamma-TiAl - based alloys. Dissertation, RWTH Aachen, Aachen, Germany (2010)

Demir, E.: Constitutive modeling of fcc single crystals and experimental study of mechanical size effects. Dissertation, RWTH Aachen, Aachen, Germany (2010)

Larour, P.: Strain rate sensitivity of automotive sheet steels: Influence of plastic strain, strain rate, temperature, microstructure, bake hardening and pre-strain. Dissertation, RWTH Aachen, Aachen, Germany (2010)

Tasan, C. C.: Micromechanical Characterization of Ductile Damage in Sheet Metal. Dissertation, TU Delft, Delft, The Netherlands (2010)

Aghajani, A.: Evolution of microstructure during long-term creep of a tempered martensite ferritic steel. Dissertation, Ruhr-University Bochum, Bochum (2009)

Huynh, N. N.: Modelling of Microstructure Evolution and Crack Opening in FCC Materials under Tension. Dissertation, Wollongong University, Wollongong New South Wales [Australia] (2009)

Balasundaram, K.: Mechanical Characterization of Viscoelastic-Plastic Soft Matter using Nanoindentation. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)

Liu, T.: High Resolution Investigation of Texture Formation Process in Diamond Films and the Related Macro-Stresses. Dissertation, Ruhr-University Bochum, Bochum [Germany] (2009)

Imlau, J.: Zusammenhang zwischen Mikrostruktur, Schädigungsverlauf und mechanischen Eigenschaften bei TRIP Stählen. Dissertation, RWTH Aachen, Aachen, Germany (2008)

Thomas, I.: Untersuchung metallphysikalischer und messtechnischer Grundlagen zur Rekristallisation und Erholung mikrolegierter IF Stähle. Dissertation, RWTH Aachen, Aachen, Germany (2008)

Cedat, D.: Modeling and Experiment on Mo-based high temperature composites. Dissertation, Ecole Centrale Paris, Laboratoire for Materials, Paris [France] (2008)

Raue, L.: Kristallographische Texturen und richtungsabhängige mechanische Eigenschaften des Exoskeletts des amerikanischen Hummers sowie Texturen weiterer Biomaterialien. Dissertation, RWTH Aachen, Aachen, Germany (2008)

Sachs, C.: Microstructure and mechanical properties of the exoskeleton of the lobster Homarus americanus as an example of a biological composite material. Dissertation, RWTH Aachen, Aachen, Germany (2008)

Zaafarani, N.: Experimental and theoretical investigation of nanoindentation in a Cu single crystal. Dissertation, RWTH Aachen, Aachen, Germany (2008)

Tjahjanto, D.: Micromechanical Modeling and Simulations of Tranformation-Induced Plasticity in Multiphase Carbon Steels. Dissertation, TU Delft, Delft, The Netherlands (2008)

Klüber, C.: Korrelation von mechanischen Eigenschaften und Kristallorientierung auf mikroskopischer und nanoskopischer Ebene. Dissertation, RWTH Aachen, Aachen, Germany (2008)

Bastos da Silva, A. F.: Characterization of the Microstructure, Grain Boundaries and Texture of Nanostructured Electrodeposited CoNi by use of EBSD. Dissertation, RWTH Aachen, Aachen, Germany (2007)

Al-Sawalmih, A.: Crystallographic Texture of the Arthropod Cuticle Using Synchrotron Wide Angle X-ray Diffraction. Dissertation, RWTH Aachen, Aachen, Germany (2007)

Detroy, S.: Charakterisierung und Entwicklung von bainitischen Multiphasen-Stählen. Dissertation, RWTH Aachen, Aachen, Germany (2007)